Arduino Lucky Shield, Multi-Sensor Shield, A000125

$0.00

感測器擴展板 Multi-sensor Shield

Out of stock

SKU: 058-31-5300;Arduino:A000125 Categories: , , , , , , , , , ,

Description

Arduino Lucky Shield集合紅外線感應器、光度感應器、濕度計、溫度計、氣壓計、磁力計、加速儀、蜂鳴器、五鍵操縱桿、兩個5V繼電器、兩個可編程按鈕，以及兩個可編程LED。使用時可配合簡單易用的官方程式庫，尤其適用於需要使用多個Sensor的Project。

Additional information

套件內容 Kit Content

1×Arduino Lucky Shield
1×BME280 breakout
輸入電壓 Input Voltage

3.3/5 Vdc from Arduino base board pins
蜂鳴器聲壓級 Buzzer Sound Pressure Level

90 dBA minimum at 10 cm
光度感測波長 Light Measurement Wavelength

Ambient 630 nm peak sensitivity
光度感測器工作溫度 Light Sensor Operating Temperature

-40~85 °C
濕度感測反應時間(τ63%) Humidity Measurement Response Time (τ63%)

1 s
濕度感測準確度公差 Humidity Measurement Accuracy Tolerance

±3 % relative humidity
濕度感測遲滯 Humidity Measurement Hysteresis

<2 % relative humidity
氣壓感測範圍 Pressure Measurement Range

300~1,100 hPa
氣壓感測RMS雜訊 Pressure Measurement RMS Noise

0.2 Pa, equivalent to 1.7 cm
氣壓感測靈敏度誤差 Pressure Measurement Sensitivity Error

±0.25 %, equivalent to 1 m at 400 m height change
氣壓感測溫度偏移係數 Pressure Measurement Temperature Coefficient Offset

±1.5 Pa/K, equivalent to ±12.6 cm at 1 °C temperature change
溫度感測範圍 Temperature Measurement Range

-40~85 °C
磁通量密度感測範圍 Magnetic Flux Density Measurement Range

±1000 μT for full-scale
磁通量密度資料輸出率 Magnetic Flux Density Data Output Rate

80 Hz
磁強計功能 Magnetometer Feature

Electronic compass
加速度感測範圍 Acceleration Measurement Range

±8 g for full-scale
加速度資料輸出時間 Acceleration Data Output Time

~700 μs
繼電器額定線圈電壓 Relay Rated Coil Voltage

5 Vdc
繼電器接點種類 Relay Contact Type

Single
繼電器額定負載 Relay Rated Load

8 A at 250 Vac resistive load
5 A at 24 Vdc resistive load
繼電器承載電流 Relay Carry Current

10 A
繼電器切換電流 Relay Switching Current

10 A for NO
8 A for NC
繼電器吸合時間 Relay Operate Time

10 ms maximum
繼電器釋放時間 Relay Release Time

5 ms maximum
用戶介面 User Interface

1×Buzzer
2×User LED (LED1~LED2)
1×Joystick as a 5-directional tact switch
2×User button (PB1~PB2)
1×LED (POWER) for indicating power
1×Reset button (RESET)
連接介面 Connection Interface

1×Set of headers in Arduino Uno form factor
1×2.54 mm 5-pin female header for BME280 breakout
1×Set of headers for OLED 128×64 with driver chip SSD1306/SSD1308
2×3-position terminal block (NC, C, NO) for each power relay
1×ICSP male header
零件接駁 Component Connection

Buzzer at pin 5
Ambient light sensor ALS-PT19-315C/L177/TR8 at pin A0/14
I2C voltage translator PCA9306 at pins 14 (SDA) and 15 (SCL)
Environmental sensor BME280, with address 0x76, at 3.3 Vdc section of PCA9306
Magnetometer MAG3110, with address 0x0E, at 3.3 Vdc section of PCA9306
Accelerometer MMA8491Q, with address 0x55, at pins 9~11 for Z/Y/X-axis data respectively, and at 3.3 Vdc section of PCA9306
OLED 128×64 with driver chip SSD1306/SSD1308 (not included in the product) with address 0x3C, at 3.3 Vdc section of PCA9306
I/O expansion I2C device CAT9555H, with address 0x20, at 3.3 Vdc section of PCA9306
PIR controller M7616 at CAT9555H IO0.3 as input
User LEDs at CAT9555H IO0.4~IO0.5 as output
Power relays G6RL-1 DC5 at CAT9555H IO0.6~IO0.7 as output
Joystick at CAT9555H IO1.0~1.4 as input
User buttons at CAT9555H IO1.5~IO1.6 as input
大小 Dimension

68.6 mm×53.4 mm
採用部件 Used Part

PUI Audio buzzer transducer SMT-0927-S-6-R
Everlight ambient light sensor surface-mount ALS-PT19-315C/L177/TR8
Texas Instruments dual birectional I2C bus and SMBus voltage-level translator PCA9306
Bosch Sensortec integrated environmental sensor unit BME280
NXP 3-axis digital magnetometer MAG3110
NXP 3-axis multifunction digital accelerometer MMA8491Q
ON Semiconductor 16-bit I2C and SMBus I/O port with interrupt CMOS device CAT9555H
Mosdesign low power PIR controller M7616
Omron low-profile 12.3 mm height power relay with maximum switching of 10A G6RL-1 DC5

Related products